Fox Express

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

Cleaning frequency. food-contact surfaces of grills, griddles, and similar cooking devices and the cavities and door seals of microwave ovens not cleaned at least once a day; except that this shall not apply to hot oil cooking and hot oil filtering equipment if it is cleaned as specified in subsection (f) of this section. the food-contact surfaces of all cooking equipment shall be kept free of crusted grease deposits and other accumulated soil.

Using chemicals for sanitization. when using chemicals for sanitization, a test kit or other device that accurately measures the concentration of the solution in parts per million or milligrams per liter not provided and used.

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

8-304.11(k) the permit holder shall notify customers that a copy of the most recent establishment inspection report is available upon request by posting a sign or placard in a location in the food establishment that is conspicuous to customers or by another method acceptable to the regulatory authority.

Materials; general. multi-use equipment and utensils not designed, constructed and repaired with safe materials, including finishing materials / not corrosion-resistant and nonabsorbent / not smooth, easily cleanable and durable under conditions of normal use.

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

Using chemicals for sanitization. when using chemicals for sanitization, a test kit or other device that accurately measures the concentration of the solution in parts per million or milligrams per liter not provided and used.

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

Toilet fixtures. toilet room not provided with at least one covered waste receptacle.

Toilet room. toilet facility / vestibule, not kept clean / not in good repair / not free of objectionable odors.

Hand-washing sink supplies. hand-washing sink or group of adjacent hand-washing sinks not provided with individual, disposable towels / a continuous towel system that supplies the user with a clean towel / a hand-drying device providing heated air or a hand-drying device that employs an air-knife system that delivers high velocity, pressurized air at ambient temperatures.

Maintaining refuse areas and enclosures. storage area / enclosure for refuse / recyclables / returnables not maintained free of items that are unnecessary to the operation or maintenance of the establishment, such as equipment that is nonfunctional or no longer used, as specified in section 20-21.28(a)(03) / not maintained clean.

Containers. in containers designed with drains, drain plugs not in place at all times, except during cleaning.

Utility line installation. exposed utility service lines and pipes not installed in a way that does not obstruct or prevent cleaning of the floor.

Floor junctures. in all new or extensively remodeled establishments utilizing concrete / terrazzo / ceramic tile / similar flooring materials, and where water flush cleaning methods are used, the junctures between walls and floors not coved / not sealed. in all other cases, the juncture between walls and floors shall not present an open seam of more than one-thirty-second of an inch.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not kept clean.

Construction. walls, including nonsupporting partitions / wall coverings / ceilings, of walk-in refrigerating units / food preparation areas / food storage areas / food display areas / equipment-washing areas / utensil-washing areas not light-colored / smooth / nonabsorbent / easily cleanable except for ceilings over areas used only for beverage preparation and/or service. concrete or pumice blocks used for interior wall construction in these locations shall be finished and sealed to provide an easily cleanable surface except in dry storage areas.

General. at least 10 foot candles (110 lux) of light not provided at a distance of 30 inches (75 cm) above the floor in walk-in refrigeration units / dry food storage areas / other areas and rooms during periods of cleaning.