Swift 101

8-304.11(k) the permit holder shall notify customers that a copy of the most recent establishment inspection report is available upon request by posting a sign or placard in a location in the food establishment that is conspicuous to customers or by another method acceptable to the regulatory authority.

General. the internal temperature of time/temperature controlled for safety (tcs) food not maintained at 41°f (05°c) or below or 135°f (57°c) or above at all times, except as otherwise provided in this article or unless a packaged product is so labeled as exempted and approved by the appropriate state or federal health authority. (corrected on site)

General. bulk food removed from original container not stored in a container identifying the food by common name. (corrected on site)

Refrigerated storage. date marking of ready to eat foods. time/temperature controlled for safety (tcs) / ready to eat food opened / prepared / packaged and held refrigerated for more than 24 hours not clearly marked to indicate “time food is opened / prepared” and “disposition date”. (corrected on site)

General. container of food not stored a minimum of 6 inches above the floor.

General. raw / prepared food removed from original containers / packages being stored in unclean containers / being stored in uncovered containers..

General. packaged / unpackaged food stored in contact with water / un-drained ice.

Dispensing utensils. no suitable dispensing utensils provided for employees / consumers during pauses in food preparation / dispensing. (corrected on site)

Materials; general. multi-use equipment and utensils not designed, constructed and repaired with safe materials, including finishing materials / not corrosion-resistant and nonabsorbent / not smooth, easily cleanable and durable under conditions of normal use.

Plumbing fixture installation. plumbing fixtures, including compartment type utensil-and-food sinks, hand-washing sinks and mop or utility sinks, not installed to preclude splashes from running down mounting surfaces behind and adjacent to the fixture. acceptable installation methods include a liquid tight seal between fixture and mounting surface, insertion into a precut counter, table or cabinet with a perimeter seal or any other effective method. all materials used shall be safe, smooth, impervious and easily cleanable.

Cleaning frequency. dry cleaning. surfaces of utensils and equipment contacting food that is not time/temperature controlled for safety (tcs) food not cleaned in equipment such as ice bins, beverage dispensing nozzles, enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment at a frequency specified by the manufacturer; or absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. this subsection does not apply when dry cleaning methods are used as specified in subitems a and b of this item.

Cleaning frequency. nonfood-contact surfaces of equipment not cleaned as often as is necessary to keep the equipment free of accumulation of dust, dirt, food particles, and other debris.

Backflow. an air gap between the water supply inlet and the flood level rim of the plumbing fixture / equipment / or nonfood equipment not at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch). a backflow or backsiphonage prevention device installed on a water supply system shall meet american society of sanitary engineering (asse) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. a backflow prevention device shall be located so that it can be serviced and maintained. a hose shall not be attached to a faucet unless a backflow prevention device is installed.

Hand-washing sink supplies. supply of hand-cleansing liquid / powder / bar soap not available at each hand-washing sink or group of two adjacent hand-washing sinks.

Containers. containers stored outside the establishment / dumpsters / compactors / compactor systems / receptacles / waste handling units for refuse / recyclables / and returnables not provided with tight-fitting lids / doors / covers, not kept covered when not in actual use. in containers designed with drains, drain plugs shall be in place at all times, except during cleaning.

Openings. outside openings not protected against the entrance of insects by filling or closing holes and other gaps along floors / walls / ceilings / tight-fitting, self-closing doors, kept closed / closed windows / screening / properly designed and installed air curtains to control flying insects / other means.

Maintenance. walls / ceilings, including doors, windows, skylights, and similar closures, not maintained in good repair.

Attachments. light fixtures / vent covers / wall-mounted fans / similar equipment not including decorative items attached to walls and ceilings not easily cleanable / not maintained in good repair / not kept clean.

Signs clearly stating that smoking is prohibited within not conspicuously posted at every entrance to a public place.